
中空玻璃打胶机的调试方法你会了吗?
时间:2025-08-24 来源:/ 发布人:昌盛机械
怎样调试卧式中空玻璃半自动打胶机放在一个平整干净的平面上,连接电源和气源,两者确认接通之后就开始进行操作。首先打开气泵开关,电源总开关,控制台开关,在控制台按手动按钮,然后在显示屏上找到原点设定,点击辅助原点设定,然后点击头部原点设定,注意原点设定时避免头部和辅助吸盘碰撞。
How to debug the semi-automatic glue machine for horizontal insulating glass? Place it on a flat and clean surface, connect the power and gas sources, and confirm that they are connected before starting the operation. Firstly, turn on the air pump switch, power main switch, and console switch. Press the manual button on the console, then find the origin setting on the display screen, click on the auxiliary origin setting, and then click on the head origin setting. Be careful to avoid collision between the head and the auxiliary suction cup when setting the origin.
等设定好然后返回找到玻璃厚度设定,先是玻璃的厚度然后是铝隔条然后还是玻璃的厚度,输入完以后,点击设置进入。等命令位置和当前位置数值一致即可,注意设置时传送带上不要有玻璃。然后是混交了,按第一桶胶按钮,按工作选择按钮,然后按拍胶启动,在按伐开,此时胶头以出胶,等看不见白胶,以混均匀以后按伐关,再按链接生产线,自动运行,此时可以自动打胶。
After setting it up, go back and find the glass thickness setting. First, the thickness of the glass, then the aluminum spacer, and finally the thickness of the glass. After entering it, click on the settings to enter. Wait until the command position matches the current position value, and be careful not to have glass on the conveyor belt during setup. Then it's mixed. Press the first glue button, press the job selection button, and then press the tapping glue start button. After pressing the tapping button, the glue head will release glue. When the white glue is no longer visible, press the tapping button to mix evenly. Then press the link production line, and it will run automatically. At this time, the glue can be automatically applied.
调试的注意事项:
Precautions for debugging:
1、在当天机器操作完毕后要把胶管内的胶冲出,防止硬化;如果长时间不实用要注意用煤油清洗胶管和胶枪。
1. After the machine operation is completed on the same day, the rubber inside the hose should be flushed out to prevent hardening; If it is not practical for a long time, pay attention to cleaning the rubber hose and gun with kerosene.
2、双组份打胶机使用的硅酮胶或聚硫胶要注意杂质不能过高,低质量的胶容易堵塞胶管的过滤系统,造成出胶不畅或不均匀。
2. The silicone or polysulfide glue used in the two-component glue machine should be careful not to have too many impurities. Low quality glue can easily block the filtering system of the rubber hose, causing poor or uneven glue output.
3、在更换胶的品种时要特别注意把双组份打胶机内残留的胶冲净,最好清洗,因为不同品种甚至品牌的胶容易反应堵塞机器。4、液压站系统的压力,不能调的太高,要根据室内环境温度等实际情况,调至满足胶嘴正常出胶均匀打胶即可。打开液压站时一定要打开胶枪,否则B组份管路压力将升得很高,造成安全事故。
3. When changing the type of glue, special attention should be paid to flushing out the residual glue in the two-component glue machine, and it is best to clean it, because different types or even brands of glue are prone to reacting and blocking the machine. 4. The pressure of the hydraulic station system cannot be adjusted too high. It should be adjusted according to the actual indoor environment temperature and other conditions to meet the normal and uniform dispensing of glue from the nozzle. When opening the hydraulic station, be sure to turn on the glue gun, otherwise the pressure in the B component pipeline will rise very high, causing a safety accident.
本文由 中空玻璃打胶机 友情奉献.更多有关的知识请点击 / 真诚的态度.为您提供为全面的服务.更多有关的知识我们将会陆续向大家奉献.敬请期待.
This article is a friendly contribution from the insulating glass gluing machine For more related knowledge, please click / Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.
- 中空玻璃打胶机的调试方法你会了吗? 2025/08/24
- 中空玻璃生产线:一条中空线至少需要几个人? 2025/08/23
- 中空玻璃生产线的性能特点 2025/08/23
- 中空玻璃生产线安装操作要注意什么? 2025/08/17
- 中空玻璃填充氩气的作用 2025/08/16
- 胶条式和铝条式中空玻璃的组装区别 2025/08/12
- 玻璃清洗机使用过程中常见问题、注意事项及维护保养相关知识 2025/08/09
- 中空玻璃设备清洗机的维护保养工作有哪些 2025/08/09
- 中空玻璃的基本制造工艺流程是什么? 2025/08/01
- 双组份打胶机详解:从设计到使用维护 2025/07/30